mechanical

Auxiliary truck lighting and 110V wiring. 

I now have a 110V cord hard wired, or permanently mounted anyway, in my truck. Run from under the center of the dash in the cab, out the firewall, and ending in the drivers side inner fender. Should come in handy for any 110V current tools I might want to run off of my power inverter. 


I’ve actually wanted to wire a setup like this in both the front and back of the truck for a while, just never got around to it.

So, Why now? your asking…

Weeeeelllll….

What do you get if I’m bored, not feeling the season, wanting to do something festive, and just plain silly fun, and have a brand new 20′ spare set of Christmas lights just laying around?

😀  😉 

Cut up a couple old cords, one from a dead fan, the other from a dead string of lights, to make a small extension cord. Cord ends wouldn’t fit through the hole in the fire wall, and I needed a custom length anyway, so I put it through, then installed the 2nd end, thus my now permanent cord.


[​IMG]

Dug out the old power inverter I cary in the truck;

[​IMG]

Lots of zip ties;

[​IMG]

And voila!

😀 


[​IMG]

[​IMG]

Yes, I know I’m a total redneck… And that I’ll Never live this one down. But its just so freaking cool to drive around! 

One guy that passed me on the 4 lane, as he went by me slowly, his passenger suddenly did a double take as they came up even with my front fender… The guy just about Garfielded himself on the window! Just so hillarious! 

That reaction alone was worth it if no one else noticed… And a lot of other people noticed. Got lots of smiles out of people on our quick trip to town last night. 

If nothing else I “lightened” up a few folks evenings, hopefully for the better… Definitely got me feeling a lot better

Next year I’m thinking I’ll hang a wreath in the middle of the grill, and light it, and run the other lights on out down the full bed length.  😀

Merry Christmas everybody.  🙂

Advertisements
Categories: Adventures, Alaska-Life, Automotive Work, Christmas, Custom, Customized, Decorating, Fabrication, Funny, GetOutdoors, Good Times, Just Plain Fun, MacGyver, MacGyverism, mechanical, Modifications, Sillly, Silly, truck, Truck gear, Winter

Time in my pocket…

New watch arrived this week. Have wanted this one for a while, but always put off getting it for something else. 


It’s a pocket watch, but it’s a bit different than the norm. 

Closed;

[​IMG]

Partially open;

[​IMG]

Open;

[​IMG]

The release is a pull button, not a push. Pull to in latch, and the inner watch swings out. Mechanical movement,the back of the inner case is windowed to see it run. 

I’m just a bit underwhelmed…. I figured it was the size of an average watch, the movement/inner part smaller to compensate for any increase in the case. 

And honestly I didn’t think it would be any bigger, just assembled different… But it is bigger. 

The diameter is about the same as an average watch, even smaller than my open faced one. 

[​IMG]

But the thickness is substantially more. And it’s HEAVY. That outer case is a Super solid casting! Not quite sure if it’s going to comfortably carry, but I’ll give it a fair go! 

[​IMG]

Otherwise it’s great though!  🙂 

Categories: EDC, mechanical, New Gear, Pocket Watches, Watches

Quartz to mechanical pocket watch conversion. V1.0

Back in mid May, I bought a cheap Chinese mechanical pocket watch. To be used as a movement donor, to fix one of my favorite quartz pocket watches that has bit the dust.  The quartz watch is special because it was one my Dad bought me.

I spent two days on ebay searching the watches for a dial/face I liked,  that was easy to read… Many mechanical watches have an unreadable color scheme,  or too much skeletonizing to be readable. 

I do like the dial in the quartz watch, but this process is a LOT easier if I don’t have to change the dial/hands between the movements. Or even remove them from the movements!


The project got shelved at the time. Then I realized how much I like the watch itself… The case is a little lightweight (cheap-ish) but it was nice enough, and went into rotation. Making it harder to canibalize for the other one.   

Every time I though of it, I put it off for various reasons.

Anyway. Today I was swapping watch chains around so I could carry my other mechanical pocket watch, and saw the quartz one on the shelf. Thought, gee wouldn’t it be nice to carry that one. And thinking how long it’s been since I carried the newer mechanical one… 

I thought oh why not, and took them apart right then. 

I always figured this would be a case of the mechanism not fitting, or the dial, or spacing ring etc, and turn out to be a real hassle to figure out.

At this point I did think that if nothing else, if it all went in ok, but the spacer ring didn’t fit, I could build a mount ring, or spacers with Sugru. 

Pulled the back covers first.

Measured the case diameters inside, quartz was 0.06″ smaller… PFFT! close enough!    

Pull plastic spacer rings, screw the crowns off (I need to find finer pliers for the next time, Victorinox Spirit tips were a bit big but worked great– you have to hold the inner shaft on the mech, and turn the crown off of it.) 

The mechanical dial was a touch smaller than the quartz one, but did fit ok. 

The mech. watches plastic ring fit the quartz case well enough, just had to whittle off some spacer nubs on its edge.. 

Room enough that the back plate went on too. 

Hands cleared the front glass. 

All perfect.

Except… 

The mechanical movement is thicker. By a few thousandths. So the stem shaft wouldn’t line up with the hole in the case/spring.  At least, not with out offsetting the dial in the case and binding the hands, and the crowns use.. 

I got that figured out with firm placement of the dial in place, and flexing/slightly bending the stem rod to line up, then starting the threads. Once started and seated it simply flexed the shafts where it needed it. 

Unfortunately…. (saw this coming, didn’t you?)

In the process,  I was handling a bare unprotected mechanical movement. That was running slightly… Somewhere I stopped it wrong, or pressed wrong,  or tweaked something… Ended up with a fine loop double up in the main spring/balance spring. 

Even if I could take it apart (oi.) I doubt I could straighten out the spring and make it work.  And I’d probably never get it back together right. 

So, at that point I had a half installed broken movement.  

I went ahead and finished the install, trimming the the plastic ring, etc.  

It all fits and would work great. If it still worked. Lol. 

So now I just need to order another of those watches to canibalize… A little more careful this time. 

Thankfully I’m only out about $12 on the broken one. It’ll still only be a $24 conversion! 😀 

Only took three pics of the whole process, will take more the next time. 


Mechanical spacer ring in quartz case;



The spring after I was done trying to push the loop out… Yeah. 😦


Categories: Custom, Damages, EDC, Improviser, MacGyver, mechanical, Modifications, New Gear, Sentimental, Sugru, Watches

Blog at WordPress.com.

%d bloggers like this: