Remodeling

Bent?

Must have caught my knife clip on something…

[IMG]

Less than a minute with the Spirit fixed it.

[IMG]

Tough clip though, was putting a lot of twist on the Spirit jaws to do it! Light build of the knife, I was a little worried about bending the frame/liner. But it worked fine.

Categories: Construction, Damages, EDC, EDC/MT use, knives, MacGyver, Multitools, Remodeling, Repairs, Work Tools, Work/Job

New At Work Pocket Tools 2.0

Well, I’ll be damned!

[IMG]

If youll remember my last pson thus topic, what i was really needing then was one of these that included an R2/S2 bit.

This one is as yoh can see 9 in 1, including an R2!
I honestly don’t count the socket sizes except maybe the 1/4″ so it 6 in 1 or 7 in 1 for me.

[IMG]

Cool setup with short and long double bits.

[IMG]

Same size as the Stanley, thankfully not any bigger. It is a touch heavier, but I had it on me, same pocket as the Stanley is usually in, all day yesterday and never knew the difference.

[IMG]

The Stanley has been performing perfectly fine for over a month, almost two actually, so i really didn’t need this change. But on principal of being what id wanted before, I went ahead and snagged it.

Cant really lose, it was almost as cheap(low cost) @$10.

Categories: Construction, EDC, New Gear, New Work Tools, Remodeling, Work Tools, Work/Job

New At Work Pocket Tools.

New for the work carry this summer.

[IMG]

I LOVE my slim compact Kobalt screwdrivers. Takes 1 bit, holds 3 in the handle. Slim and light.
But also deathly slow, and a bit fiddly with gloves on, to change bits.
Broke down and got a cheap 6 in 1. (4 drivers, 2 nut drivers… the later of which I will rarely if ever use) Cheapest, lightest one they had. Its bulky, but actually not too heavy. Stanley, like $3.
Dont like the special double ended bits, cant just use any old 1.5″ 1/4″ drive bit. And No R2 bit.
Will see how long it lasts. If I can do ok on the bits, I might take the handle to the bandsaw and slim it down.

;)

Anyone know where I can get the fancy double ended 5/16″ hex bit it takes, or the 1/4″, in a R2/P2, or R2/1/4″ flat even, let me know.
The cutters were the cheapest also, but are good and solid. Didn’t feel like paying $22 for Chanellock. This was $10.
The ones I have are great for my auto wiring/electronic projects, and are pretty heavy duty, even good for average home wiring. But for construction site use where you cut romex, and things other than wire, I needed a set with the shorter jaw/high torque pivot location. Thankfully not much bigger than the others, and about the same weight
The old and new

20200513_195852.jpg

20200513_195901.jpg

20200513_195306.jpg

20200513_195334.jpg

20200513_195421.jpg

I got gloves again too. Been wearing deerskin learher of the same brand last season, and so far this one… But we’re doing vapor barrier now, and black death is impossible to remove from leather gloves, worse than it is from your hands. And those leather suckers are $22 a pair. (Yes, I won’t buy side cutters that’ll last a decade for $22, but I will pay that for gloves that last about 7 months. Yes, I know I’m odd. ) these are almost as comfortable after a day or two, and probably almost as durable. I just cry less when theyre ruined.

(for those that don’t know, black death is the slang term for a non hardening, non setting, forever sticky acoustical and vapor barier sealant and adheasive. It never dries or sets, and is tacky like tar. Its impossible to get off you once you get it on you. Gasoline or paint thinner will eat it. In my experience even then its hard to get off. )

Also grabbed one of these little guys. Figured why not, @ $0.97

:D

20200513_195928.jpg

20200513_195959.jpg

So, its interesting. The big yellow Stanley takes a 1/4″ bit on one end only, on the other it is 5/16″.

In this little Stanley, the bits are Smaller than 1/4″. BUT it looks like the tool is molded at the ends to take 1/4″ bits. Except it doesnt quote fit a [img] g4″ bit. The smaller bits are gripped further into the handle though. Strange.

Categories: Construction, EDC, New Gear, New Work Tools, Remodeling, Work Tools, Work/Job

Blog at WordPress.com.

%d bloggers like this: