ATV Accessories

Higher Work?

Got really really tired of everything being too low to work on, even sitting down…

 I do have a hydraulic motorcycle/atv lift, but it goes under the frame only, isn’t really stable for this type of work. 

I’ve also done stuff with it on my wheel ramps before, about 9″ of lift, but that’s still a PITA at times. 

Thus, my redneck Alaskan ATV lift.

My two old truck boxes (one a Rubbermaid chest, I wasn’t sure if it would take it, but it seems to not care about the weight! ), some scrap 2×12, and voila 16″ of lift! 

Front box being wider turned out great, didn’t plan it, but it’s enough to straddle and sit on, or stand on if needed.

Should have took pics of the first try getting it up there… Used my wheel ramps and one turned over after the front wheels when up… Was awkward getting it off at an angle with no ramp under one side. Lol. 

Categories: Alaska-Life, ATV, ATV Accessories, ATVing, Custom, Improviser, MacGyver, MacGyverism, Modifications, Repurpose, Vehicles, Wrenching

ATV Auxiliary Fuse Block

I got tired of running everythi g straight off the battery… Was running out of space for the wires around the terminals too.   

A lot you don’t get to see here, like removal of the front inner fenders,  pulling the rack and tank cover, and routing wires… 

I have it now run as;

Battery-> main fuse-> key switch-> signal into relay-> 

And the battery-> relay(switched)-> fuse panel.

I tapped the keyed hot wire that I previously tapped for winch switch signal, -what was the speedometer power wire-.
That activates an 80A relay. The relay hot activates a heavy 10ga wire from the battery, to the new fuse block.  I didn’t have one on hand, so later I need to add a heavy 60A or 70A fuse between the battery and the relay. 

Relay wiring;

Battery box wiring, fuse for relay activation is the black spade holder center frame.

Relay next to battery

Also found that even with key off, I have 0.10V after the relay… It’s bleeding power. But there is no amperage there, so no drain, it’s fine. (Or so my electronics technician friend tells me 😉 ).

The box will also house a switch panel when I’m done, thus it’s placement on the fender(and honestly it’s getting hard to find places to put wiring on this thing!)

When done I’ll have that fancy split wire loom/cover stuff on the wires. Will also silicone seal all box holes, and some connections.

Categories: ATV, ATV Accessories, Custom, Modifications, Vehicles, Wiring

ATV Rear bumper/brush guard

After I got the front guard on, on my trail ride test run, the day I posted about, I also did some brush busting. Going forward was great, a lot less worry with that push bar, I was plowing over sma 2″ to 3″ diameter trees! 

But when I couldn’t get through where I was trying to make a trail, turning around meant a 12(more like 20!) point turn in narrow quarters, pushing against/over what I had to… And it was a lot of pushing against the rear rack, rack walls, and fenders. 

Decided then that I need a rear bumper/guard. 

Lots of research later, I decided on the simple tube bumper style, and preferably one big tube. Hoping I could get curved ends.. 

To the scrap pile we go!

Bunk bed frame ends, just happened to be wider than the racks and plastic, but narrow enough to match overall… 

Some creative cutting, and more cutting… 

Amazed me, those 3/8″ cross bars were solid, not tubing! 

Mock up of Mount positioning…

Simple brackets, angle irons welded into slits cut in the tube. 

Getting it all squared and oriented right, those slits aligned, and the brackets squared in to get the curved bumper ends level/square was a pain… But worth it.  

And some welding, which I didn’t get pics of.  Worked out perfect… Ran everything together, got it all. Then decided to touch up a spot, ran about 1/4″ of bead, and the wire stopped… Ran out of welding wire right there! (Man, that roll went FAST!!)
Had to move the winch fairlead down about 3/4″ to clear. Was easier to do that than notch the tube. 😉

 Voila, crooked bumper mounted. 😉 

I’d squared and leveled it to my accessory receivers… Forgot that the left side of the rack is still tweeked down a little, thus that tube is low on that side as well.  

Adjusted the mount holes, little bigger for some tilt, and thus a level bumper!  

Not sure I like the clearance I ended with. The rack wall corners stick out further than the bumper corners.

And everything else is only an inch, or two inside it…  The idea was a brush guard more than anything, and a push bar so I don’t push with plastic or rack, and it should accomplish that.

  Will run it for a while and see if I need it spaced out some (thinking 1″ max), but I *think* it’s ok. 

Also wasn’t thrilled about the winch roller fairlead being recessed slightly.. But it’d take an extreme upward cable angle for it to rub the bumper, so that too *should* be fine. I didn’t want to space the fairlead out very far, reducing it’s stiffness to its bracket (figure all the pull of the winch, and weight of the wheeler rides on this rollers when in use!).

Amyway, thar she be!

Categories: ATV, ATV Accessories, Custom, Fabrication, Modifications, Recycle, Repurpose, Scrounging, Vehicles, Welding

Blog at WordPress.com.

%d bloggers like this: